Search Results

It is widely known that pellet-typed catalysts are deactivated by phosphorus (ZnDTP) that comes from engine oils. In this paper, the poisoning of monolithic three-way catalysts and oxygen sensors by engine oils is studied. First, catalysts and oxygen sensors were poisoned on the engine bench by test oils in which the quantity of phosphorus and ash was varied. Next, performance of the catalysts and sensors alone was examined and the vehicle exhaust emission at FTP mode was measured on a chassis dynamometer. The results indicate that phosphorus in engine oils poisons the monolithic catalyst and the oxygen sensor resulting in deterioration of the vehicle NOx exhaust emission. However, Ca sulfonate and Mg sulfonate detergents act by restraining phosphorus poisoning of the catalyst and the oxygen sensor. Through analysis of the catalyst and sensor surfaces, it is concluded that phosphorus poisons the catalyst and sensor forming a dense coating.

The authors have developed an intelligent four-wheel drive system (I-4WD) designed to distribute the driving force to the front and rear wheels at the optimum ratio according to the running condition of the vehicle. The I-4WD consists of a center differential which distributes 30 percent of the driving force to front wheels and 70 percent to rear wheels (30:70), a hydraulic multi-disk clutch, an electronic control unit and a hydraulic control circuit. The driving force distribution can be steplessly varied from 30:70 up to the rigid state by controlling the hydraulic pressure on the clutch. The main control algorithm is based on the“yaw velocity model following control.” This composition has allowed us to accurately balance the cornering performance and stability without spoiling the critical limit predictability which is that the driver knows in advance the critical limit of vehicle dynamics.

Instrument clusters used in automobiles play an important role as man-machine interface. A variety of information about the current driving situation is conveyed to the driver quickly and accurately. A great interest has been taken in the high visibility and legibility of the head-up display (subsequently abbreviated as HUD). Originally developed as display used in aeronautical applications, we have tried to exploit ways to adapt this device for automotive use. We have succeeded to produce a new HUD system, which has the following design features; (1) High brightness and high contrast display device using a liquid crystal display (subsequently abbreviated as LCD) and a halogen lamp illumination. (2) Long focus display in two colors using holographic lens. (3) Automatic dimming control system using an illuminance sensor. (see Fig. 1)

NASS 80-88 passenger side impacts data were analyzed. Location of primary car damage using the CDC classification, the AIS for injury severity studies, and the interior contacts of the various body areas. Drivers alone, or with passengers were studied separately in both left and right side crashes. Direct impacts to the passenger compartment only are less frequent than to other CDC side zones. Driver interior contacts vary by body region but also by side impacted in the crash. The presence of an unrestrained front passenger appears to enhance driver injury level in left side crashes but the presence of a passenger, in right side crashes appears to moderate driver injury severity.

Hydraulic fluids for automotive chassis systems are expected to have excellent low-temperature fluidity to get quick response at low temperature. A synthetic active suspension fluid has been designed by analyzing viscosity-temperature characteristics of Poly Methacrylate (PMA) / Poly a -Olefin (PAO) or diester mixtures based on the theoretical formula proposed by Carrasco et al. Measured kinematic viscosities are correlated with calculated ones very well at high temperature. On the other hand, there is some difference between measured and calculated low-temperature viscosities due to wax crystallization resulting from the mineral oils used as carrier oil of polymers. The theoretical formula of Carrasco et al. is applicable to polymer / synthetic base fluid mixtures even under the arctic condition in the case of no wax crystallization.

This paper describes the development of one-piece die cast magnesium steering wheel frame for a steering wheel incorporating an air bag system. The light weight magnesium frame was designed to have proper stiffness, strength and characteristics of energy absorption. Magnesium alloys with various aluminum contents were tested, and AM60B alloy was selected because of its favorable properties of strength and elongation. New manufacturing techniques, for example, a vacuum hot chamber die casting system and a surface defect inspection system were developed in order to produce high quality castings. The characteristics of energy absorption were evaluated in the laboratory and on actual vehicle crash test, and the results were satisfactory. The magnesium steering wheel frame is about 45% (550g) lighter than the steel one. It has been in production in Toyota passenger cars with driver side air bags.

A highly reliable all-mechanical air bag system has been developed with a production cost lower than the electrical air bag system. All components, such as the bag, inflator and sensor are integrated into the steering wheel. Regarding the sensor design, we first discussed the requirements of the sensor to optimize the driver's protection, and then we designed it using a simulation method. We have confirmed by crash tests that this method is correct, and have found that this system is effective for reducing facial injuries.

With the progress of super computers in recent years, a number of studies on “Computational Fluid Dynamics” (CFD) have been carried out, and various schemes for Navier-Stokes equations have been presented. Similar methods have also been applied to automotive engineering - aerodynamics, for exampre - in order to determine flow phenomena. In this paper, the application of numerical simulations to the flow cavitation that occurs in some part of orifices in the vehicle hydraulic system, will be discussed. Authors have developed a CFD program for the clarification of flow phenomena in such orifices. Using the relationship between calculated results and measured results of noise levels in such orifices, a new method for estimation of the occurrence of flow cavitation has also been developed. As a result, a new orifice configuration capable of preventing the cavitation has been designed.

This paper describes an analysis of the rise in timing belt temperature occuring under high engine speed operation that was made to establish the cause of heat deterioration of the belt materials. Surface temperatures of the belt were accurately measured by correcting thermo-vision detected radiations to eliminate environmental radiation. The temperature profile of a belt cross-section was obtained by a specially developed thermo-couple device. The experimental results indicated that heat generated by the belt contributes significantly to the temperature rise and that the primary cause of the heat generation is bending hysteresis of the belt cords. In addition, a description is made of a method of calculating the rate of heat generation in the belt. In this simulation method, the energy dissipated as heat is calculated from the bending strains and loss moduli of the belt materials. Calculated results were found to agree well with experimental results.

Display devices are required to have some fundamental functions which are brightness & gradation, colorfullness, resolution & sharpness, response time, and suitable size of the picture. Since the CRT (Cathode Ray Tube) is superior to the other display devices in these requirements, it can offer much information efficiently and effectively. Their visibility should not be evaluated only on the basis of some standards for office automation systems. From the point of view of human factors, visibility investigations of the CRTs for automobiles are examined. In this paper the relationship between the chromaticity difference and the luminance contrast for drivers to read the picture easily, and the luminance of the background in the CRTs for drivers not to be dazzled in the nighttime driving are clarified.

A system to measure transient temperature distribution on the brake disc rotor at high speed braking has been developed and its measuring principle and configuration were discussed in this paper. This system consists of two revolution sensors and two sets of optical fiber array, photoelectric elements, and microprocessor, which fiber array is so arranged that it faces the brake disc rotor. This new system has the following features: (1) Measuring is made using a visible radiation wavelength range for red hot temperatures higher than 550°C.

The deactivation process of automotive catalysts by lead and phosphoruos were studied. The accelerated poisoning test were performed. The activity evaluation and characterisation of poisoned pellet oxidation catalysts showed the following origin of poisoning deactivations. Lead interacts with active materials and phosphorus covers over catalysts to reduce these catalytic performance. In the case of phosphorus and lead co-existence, the activity decreases rapidly because leadphosphate plugges pores of the support. In monolithic catalysts, highly axial distributions of poisons was obserbed. This characteristic distribution is advantageous for the durability of the catalyst.

This paper describes a three-dimensional crash simulation program code-named ‘CRASH’ and its evaluation. This program predicts body deformation behavior of an automotive vehicle in a crash. In the program the body is represented by a structure consisting of beam elements. The inelastic deformation is calculated with the simplified constitutive equation using the yielding function. Reduced load carrying capacities due to local deformations are considered by means of representative static load-deformation curves obtained by experiments. Deformation behavior of the structural members with the above properties are analyzed with direct integration scheme taking the strain rate effects into consideration. Large displacements of structural members are also accurately calculated with the coordinate transformation matrices taking account of the finite rotations.

This paper summarizes the results of Phase 1, Concept Definition, of the AATD program and identifies the reasons such a new test device is needed. The following areas are addressed: 1) injury priority from accident data; 2) current dummy design, use, and potential improvements; and 3) technical characteristics and design concepts for a new AATD, its data processing, and its certification systems.

Lap-shoulder belt effectiveness has been indicated by many authors, however there is minimal information on the more severe injuries to lap-shoulder belted car occupants. This paper presents details of 15 lap-shoulder belted occupants in frontal collisions and 24 lap-shoulder belted occupants in side impact collisions. Case descriptions of these crashes are presented, each including vehicle, environmental and injury details.

Properties of the human neck which may influence a person's susceptibility to “whiplash” injury during lateral impact have been studied in 96 normal subjects. Subjects were chosen on the basis of age, sex, and stature and data were grouped into six primary categories based on sex (F, M) and age (18-24, 35-44, 62-74). The data include: measures of head, neck and body anthropometry in standing and simulated automotive seating positions, three-dimensional range of motion of the head and neck, head/neck response to low-level acceleration, and both stretch reflex time and voluntary isometric muscle force in the lateral direction. Reflex times are found to vary from about 30 to 70 ms with young and middle aged persons having faster times than older persons, and females having faster times than males. Muscle strength decreases with age and males are, on the average, stronger than females.

Although over 800 references to child and infant anthropometry are in the literature, most have limited validity and application to current populations. Functional measures required by industry and government for federal safety standards for design of dummies, child products, furniture, or protective devices such as restraint systems have either been incomplete, inadequate, or nonexistent. Some of the limitations influencing validity of existing data have been outlined for the potential user. As a start toward obtaining necessary functional anthropometric data, The University of Michigan is currently conducting a study sponsored by the U.S. Consumer Product Safety Commission to obtain valid nationwide measurements on a representative U.S. population from birth to age 12 years. In this study some 41 measurements, including many functional measures, as well as seated and supine whole-body centers of gravity, are being taken utilizing a new automated anthropometric minicomputer system.

APPLICATION of nuclear energy for civilian automotive uses has possibilities, these authors say. Nuclear power for automotive applications, they feel, is technically feasible now where size and weight are not prime considerations; where size and weight are major parameters, discoveries of new materials for construction of nuclear-power reactors must be made. New materials are needed for reactor fuels, heat extractants, neutron reflectors, reactor construction materials, controls, and radiation shields which must have unique nuclear properties in addition to conventional engineering properties. This paper presents nuclear automotive propulsion devices in terms of technologies now available. The necessary radiation-shielding mass and weight requirements are presented for an ideal point-source nuclear-heat-power engine.